6540A REV C Norge Washer Parts List

D-shaped knob clip (dryer metal knob clip insert)

This control knob clip helps secure the timer knob to the shaft allowing you to select the desired setting for your dryer. If the knob has become loose or the clip is missing you will need to replace the clip. This clip is a genuine OEM part, made of metal and is sold individually.

Meat drawer rail - right side (drawer support rail - right side)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Rear drum bearing kit (shaft)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Front glide kit

The front glide helps the drum rotate smoothly and quietly while operating. If your dryer will not tumble or is noisy, the glide could be worn down, causing a metal on metal noise, and will need to be replaced. It is recommended to replace both glides at the same time; a rivet tool is required for this installation. This kit includes a blue plastic glide, a brown cork pad, and two metallic rivets. The front drum glide kit is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Upper crisper drawer cover - glass not included (upper crisper drawer cover)

This cover holds up the top crisper drawer, and has drawer glides molded in it. This upper crisper drawer cover is a manufacturer-approved replacement part for your refrigerator. It has drawer glides molded into the frame but this part does not include the glass cover. To replace this part, lift out the glass cover and snap out the drawer frame. Snap this new frame cover into place and replace the glass.

Crisper drawer cover (cover pan low)

This crisper drawer cover has the drawer slides built into it to allow the crisper drawer to slide in and out. This model measures 24 1/2 inches long x 19 inches wide x 2 5/8 inches deep, is made of plastic and is white in color. If the cover becomes cracked or damaged, you will need to replace it. This is a genuine OEM part.

Flat style oven igniter kit (igniter glowbar broiler)

The flat style oven igniter is used to ignite the gas to light the oven burner in your range. If your oven is not heating, check the igniter to make sure it is glowing. If the igniter is glowing and your oven is not heating, then your igniter is not strong enough to heat the oven and you will need to replace it. When replacing the igniter please be very careful not to touch the black element part of the igniter as it is very fragile. The part measures approximately 3-3/4" in length and the amperage range is 3.3 to 3.6. The kit comes with a mounting bracket and a wire connector with a plug. *Please note: the connector plug might need to be removed and spliced to the range wiring using porcelain wire nuts. This is a genuine OEM part.

Refrigerator ice and water filter (canister water filter)

Replacement ice maker

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Refrigerator water filter (use wf2cb)

This is a single OEM water filter used in refrigerators to remove impurities and particles from water that goes through the water and ice dispenser. It is used for reducing cysts, turbidity, lead, mercury, herbicides, and more. If your icemaker is not making ice, not dispensing ice, dispenses too little ice, or there is leakage and the fridge is making loud noises, replacing the water filter may be the solution. This filter is located in the front, top right of side-by-side refrigerators. You will know it is time for a new filter when the light on the freezer door dispenser lights up red, or after 6 months (200 gallons) of use. No tools are required for this easy repair. First, press the release button to pull out the old water filter and push and lock in the new water filter. Run water through the dispenser for about 3 minutes to prime the filter for use. Dispose of the water or use it to water plants. Press the indicator for 3-10 seconds to reset after this repair is complete. This carbon-based filter measures 6 x 3 x 7 Inches and is white plastic. Note: You may also need to order the water filter base to make the water filter fit properly. Please use your model number to locate the filter base.

Door rack (rack-door)

This OEM door rack for your refrigerator is sold individually.

Water filter (use wf1cb)

Manufacturer's Number: WFCB The PureSourcePlus filter fits refrigerators made before 2001, and Kenmore refrigerators with model numbers starting with 253. This filter has white ends, while the EAP503619 has blue ends. May require the EAP428513 wrench or EAP428532 O-ring. Filters for: Taste and odor Sediment 99.3% of Lead 99.99% of Cysts 99.7% of Turbidity 99.8% of Particulates (Class I) 94.9% of Atrazine (a herbicide) 94.2% of 2,4-D (a herbicide) 97.8% of Chlorine (Class I) 87.5% of Toxaphene (a pesticide)

Refrigerator door shelf bin (bin-door, refrig pseudo, 2 lt)

Front drawer glide (drawer glide)

This front drawer glide is for your bottom range drawer. As the broiler drawer slides back and forth, these glides prevent metal-to-metal contact and offer support for the drawer. If you are having trouble opening and closing the broiler drawer, the glide may be broken and will need to be replaced. Your range has 4 in total – 2 front and 2 rear. This is a genuine OEM part and is sold individually.

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.